Speed Loader For FX Impact

This is a 3D printed Speed Loader for the FX impact MK2 Side-Shot Hi-Cap Magazine.

.25Cal / 6.35mm – 28Rnds
.22Cal / 5.5mm – 28Rnds
.30Cal / 7.62mm – 23Rnds

You don’t need extra expensive magazines if you have this, it’s almost the same thing. Makes life much easier loading your pellets. Superfast loading.

Price per unit: $18.00
Shipping: $5.00
Shipping for each additional: $3.00

Speed Loader For FX Crown, Maverick, Dreamline and WildCat MKIII

This is a 3D printed speed loader for the new MKIII Side-Shot Hi-Cap Rotary Magazines

Price per unit: $18.00

Shipping: $5.00

Shipping for each additional: $3.00

This is a 3D printed part that closes the gap between the tank and the barrel and helps with the harmonic tuning by eliminating the up and down barrel vibrations after every shot. Testing shows more consistency and better groups.

IMPORTANT
Install at the front end of the tank as shown in picture.After installing, re-zero MUST be done to the scope because the POI will be shifted upward.

Price per unit: $12.00
Shipping: $5.00
Shipping for each additional: $3.00

This is an fx pocket chronograph tank bracket and a tube covered with carbon sticker(its not a carbon fiber tube)
Can be mounted on any FX impact 480cc Tank.
It can be adjusted back and forth for the shooters needs.
With this bracket you Eliminate POI shift that usually happens when adding the fx radar on the barrel.
Consistent FPS readings in every shot!

(Please note that this is designed to work with the original FX moderator/silencer.
Using an aftermarket silencer might make the barrel heavier and close the gap between the tank and barrel tube)

Price per unit: $25.00
Shipping: $9.00
Shipping for each additional: $6.00

This is a 3D printed Picatinny Side Shot High Capacity Magazine Holder for FX Impact Mk2 magazines.

Suitable for all Impact MK2 side shot high capacity magazines .177 .22 .25 and .30 Cal

Perfect solution for your secondary magazine. (Magazine in pictures not included)

Price per unit: $25.00
Shipping: $6.00
Shipping for each additional: $3.00

This is a 3D printed C1 Hammer seat removal tool . Just insert it in the Hammer seat, screw the bolt and easily remove the C1 hammer seat. Perfect tool for you fx impact tool kit.

Price: $10.00
Shipping: $5.00
Shipping for each additional: $2.00

Adjustable Butt Stock For FX Impact

This 3D printed adjustable butt stock is designed to fit the FX Impact MK1 MK2

Its made from durable EVO PLA material.

Can be adjusted for left and right shoulder shooting needs, Wings move up and down for better shoulder grip.

Easy installation by simply removing the bolt that holds the original pad in position and inserting the new stock.

(Bolts dont need to be over tighten)

Price: $29.00
Shipping: $12.00
Shipping for each additional: $6.00

Single Shot Loading Tray For FX Impact MK1 & MK2

This loading trays are Printed with durable ABS and are available in all calibers (.177 – .22 – .25 – .30)

Simple and very easy to use. Needs at least 2 rubber balls to work.

Price: $12.00
Shipping: $5.00
Shipping for each additional: $2.00

Payment And Shipping

All items are send with registered Shipping.
Usually will dispatch in 2-3 Business Days. In case of low stock, dispatches could take up to a week.
Only PayPal Payments Accepted.
Please contact me at [email protected] and add the items you want, the quantity and address
and i will get back to you with a PayPal invoice.

This is a 3D printed Speed Loader for the FX impact MK2 Side-Shot Hi-Cap Magazine.

.25Cal / 6.35mm – 28Rnds.22Cal / 5.5mm – 28Rnds.30Cal / 7.62mm – 23Rnds

You don’t need extra expensive magazines if you have this, it’s almost the same thing. Makes life much easier loading your pellets. Superfast loading.

Price per unit: $18.00Shipping: $5.00Shipping for each additional: $3.00

This is a 3D printed part that closes the gap between the tank and the barrel and helps with the harmonic tuning by eliminating the up and down barrel vibrations after every shot. Testing shows more consistency and better groups.

IMPORTANTInstall at the front end of the tank as shown in picture.After installing, re-zero MUST be done to the scope because the POI will be shifted upward.

Price per unit: $12.00Shipping: $5.00Shipping for each additional: $3.00

(Please note that this is designed to work with the original FX moderator/silencer. Using an aftermarket silencer might make the barrel heavier and close the gap between the tank and barrel tube)

Price per unit: $25.00Shipping: $9.00Shipping for each additional: $6.00

Price per unit: $25.00Shipping: $6.00Shipping for each additional: $3.00